Hydraulic rotating joint: 0040 251.0
General description
An overview of the different housing options is shown below:
The overview of suitable adapters is listed below.
Examples of complete configurations are shown in the figure below.
FLUITRONICS is a specialist in the development and manufacture of customer-specific series solutions in the field of drive technology and control. If you cannot find any suitable products in our database, please contact us or visit our homepage (www.fluitronics.com). We would be happy to show you what the path to your individual solution can look like.
With the help of the hydraulic rotary union, the hydraulic pressure supply can be provided during a relative rotational movement. The rotating union is available in axial and radial construction. Sealing designs for the connection are available as O-ring (OR) and ED sealing. The entire kit has the following special features:
- Spring preloaded bearings, thus less sensitive to vibrations.
- Different throttling holes in the trunnion (Ø1.0 to max. Ø2.5)
- Outer bearings with RS sealing. Thus better protection against penetrating water and dirt
- Screw-in housing with galvanic coating flZn-nc-480h-, or ISO19598-Fe//ZnNi-8-Cn-T0. Protection against base material corrosion (salt spray test according to ISO 9227) at least 480h
- Connecting parts, i.e. elbows and SDS screw-in studs, with galvanic coating (class K3 according to CN040201 - chap. 3.6.3 in conjunction with Table 4) Protection against base material corrosion (according to ISO 9227) at least 288h.
- All pins with wear-reducing PVD coating
Function
The kit consists of housing, spigot and connector. Available options are shown in the following diagram.An overview of the different housing options is shown below:
The overview of suitable adapters is listed below.
Examples of complete configurations are shown in the figure below.
Details
The hydraulic rotating union 1799 240.0 has a M20x1.5 housing connection with ED seal in radial design. The consumer connection is 8L.
Available configurationsThe configuration key of the KH aggregate series is shown below.
FLUITRONICS is a specialist in the development and manufacture of customer-specific series solutions in the field of drive technology and control. If you cannot find any suitable products in our database, please contact us or visit our homepage (www.fluitronics.com). We would be happy to show you what the path to your individual solution can look like.
Technical conditions Medium pressure applications
Maximum pressure Pmax: 210barMaximum speed nmax. (210bar): 1800 1/min
Technical conditions for low pressure applications
Maximum pressure Pmax: 40barMaximum speed nmax. (40bar): 2100 1/min
Fluid requirement
Fluid: Mineral oil HL/HLP 32/46 according to DIN 51 524Ambient temperature: -25°C - +60°C
Oil temperature: -25°C - +85°C
Viscosity: 20 - 400cSt
Oil purity: 20/18/14 ISO4406
O-ring seals: NBR 90Shore A
Screw-in thread / Tightening torque
M20x1,5-ED ISO9974 80 +8 NmM22x1.5-OR DIN ISO6149-1 80 +8 Nm
M30x2-OR DIN ISO6149-1 130 +8 Nm
M33x2-OR DIN ISO6149-1 80 +8Nm
Assembly instructions
- Carry out all assembly work with the utmost care and cleanliness!
- Always protect the shaft end from contamination, but never clean it with industrial cleaners - DRY RUNNING of the seal can lead to premature failure.
- Never direct the jet of a high pressure or steam cleaner directly at the bearing seal!
- Important for a long service life is a good concentricity during operation and a distortion-free installation. For this purpose, mount the rotating unions with the specified torque and then connect the hose lines in a curved and torsion-free manner. If necessary, mount hose clamps only after the bend.
- After installation, check that the rotating union can be rotated easily.
C
The following seals are available as accessories:
Hydraulische Drehdurchführung
STEP-File